[. . . ] Product Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 2 4 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 1 1 2 4 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Prepare for Installation Thank you for purchasing TRENDnet's TPE-101I Injector/TPE-104S Splitter. If you run into problems, please refer to the Troubleshooting section of this guide. If you need further technical support, please visit www. TRENDNET. com or call technical support by phone. Verify Package Contents Please make sure you have everything in the box: TPE-101I/TPE-104S Injector/Splitter User's Guide Injecteur TPE-101I /Splitter TPE-104S Guide de l'utilisateur TPE-101I Injector/TPE-104S Splitter Benutzeranleitung Guía del Usuario inyector TPE-101I/ splitter TPE-104S Version 01. 04. 05 TRENDnet TRENDware, USA What's Next in Networking Copyright ©2004. TRENDware International, Inc. TPE-101I/TPE102S User's Guide Power Cable Jumper Cable Power Adapter (48V, 500mA) 1 English 2. Product Detail TPE-101I The TPE-101I has a RJ-45 connector for data, a RJ-45 connector for Powerover-Ethernet, and a power adapter connector. It also has two LEDS that indicate power and Power-over Ethernet. LED for Power Adapter LED for Power-over-Ethernet RJ-45 connector for Power-over-Ethernet Jumper Cable Connector RJ-45 connector for Data 2 English TPE-104S The TPE-104S has a RJ-45 connector for Power-over-Ethernet, a RJ-45 connector for data, and a jumper cable connector. A4: Non-PoE devices such as access points will work with the TPE-104S only if the non-PoE device operates at 5V. Q5: I connected my non-PoE device into the TPE-104S, but my switch does not recognize the device. A5: Power cycle the non-PoE device by either pulling out the power adapter connector from the PoE injector or disconnecting the CAT 5 cable from the PoE OUT port. If you have further questions, please contact Trendware's Technical Support Department. Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received including interference that may cause undesired operation. 7 Product Warranty Registration Please take a moment to register your product online. [. . . ] Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received including interference that may cause undesired operation. 7 Product Warranty Registration Please take a moment to register your product online. [. . . ]